Expert GE Appliances Appliance Repair in Texas
Factory-trained technicians • Genuine parts • Same-day service
Real Repairs by Our Technicians
GE Appliances Appliances We Service
Refrigerator
GE Appliances Refrigerator Repair
Washer
GE Appliances Washer Repair
Dryer
GE Appliances Dryer Repair
Dishwasher
GE Appliances Dishwasher Repair
Oven/Stove
GE Appliances Oven/Stove Repair
Range
GE Appliances Range Repair
Cooktop
GE Appliances Cooktop Repair
Freezer
GE Appliances Freezer Repair
Range Hood
GE Appliances Range Hood Repair
Ice Maker
GE Appliances Ice Maker Repair
Built-In Oven
GE Appliances Built-In Oven Repair
Wine Cooler
GE Appliances Wine Cooler Repair
Why Choose Us for GE Appliances Repairs?
GE Appliances Specialists
Factory-trained on all GE Appliances appliances
Same-Day Service
Fast appointments throughout Texas
Genuine Parts
Only authentic GE Appliances replacement parts
Fully Insured
Insured for your peace of mind
Max Appliance Repair services GE, GE Profile, Cafe and Monogram refrigerators, washers, dryers, dishwashers, ranges and wall ovens across the Houston, Dallas-Fort Worth, Austin and San Antonio areas. Same-day appointments are available on most weekdays. Call (888) 771-3235 or book online.
Last updated November 2026
GE Appliances has been owned by Haier since 2016, but the products are still engineered and built largely in the United States, and the control logic across GE, GE Profile, Cafe and Monogram lines is shared. That matters for a repair: one diagnostic approach covers a budget GE top-load washer and a Cafe French-door refrigerator, parts are stocked widely, and many GE models put a readable fault code on the display instead of just a blinking light. Our technicians work on the current UltraFresh front-loaders, the deep-fill top-loaders, the TwinChill and side-by-side refrigerators, Profile and Cafe dishwashers and the slide-in ranges with air fry, and they carry the common GE wear parts on the van so most visits end with a working appliance.
GE machines in Texas fail in a few predictable ways. Hard water across Dallas-Fort Worth, Austin and San Antonio scales up dishwasher heaters and inlet screens, which is why C6 and H2O messages show up long before the appliance is old. In Houston the combination of humidity and long dryer vent runs through attics makes no-heat and two-cycle drying the most frequent GE dryer call, and the vent, not the dryer, is usually the cause. Summer storms leave PF notices on GE refrigerators and dishwashers that clear with a reset; a PF that keeps returning on a calm week points at the outlet or the control.
Common GE Appliances Issues
Range or wall oven shows F2, F3, F4, F7 or F9
GE publishes what these codes mean. F2 (or F20) means the oven temperature went above its limit; let the oven cool, press Clear/Off and try again, and if it repeats the control or a stuck relay needs service. F3 and F4 both point at the oven temperature sensor, the thin probe on the back wall of the cavity: the sensor or its connector is replaced. F0, F1 and F7 mean the touch panel or the electronic control is misreading a key; a 30-second power cut at the breaker sometimes clears it, a repeat means the panel. F9 and FC mean a fault in the door-lock circuit, which usually appears after a self-clean cycle. ERR is not a fault: the entry was invalid, and an oven that will not go above 290 is set to Celsius.
Oven not heating, baking unevenly or self-clean locked the door
On electric GE ranges a bake element with a visible blister or break explains an oven that stays cold while the broiler works. On gas models an igniter that glows for more than a minute without lighting the burner is weak and should be replaced before it fails completely. Uneven baking with no code is usually the sensor drifting or a convection fan that stopped. If the door stayed locked after a self-clean cycle, wait for the oven to cool fully; a door that is still locked an hour later has a lock motor or switch problem.
Dishwasher stops with C1, C2, C3, C4, C5, C8, H2O or PrS
GE dishwashers use C-codes, and they split by stage. C1 means draining took more than two minutes and C2 more than seven: clean the air gap on the sink, check that the drain hose has a high loop and is not kinked, and run the garbage disposer; on a new disposer make sure the knockout plug was removed. C3 means the dishwasher will not drain at all. C4 means the tub filled twice after a power failure or the float is stuck: tap the float cover in the front left corner of the tub floor and clear the sump. C5 means the pump-out was too short, which usually means low water; check that the supply valve is open. C8 means something in the lower rack blocks the detergent cup from opening. H2O means low water: look for a kinked inlet hose and a half-closed valve, and if it appears only on the 1-Hour Wash cycle, book service. PrS means the pressure sensor sends an invalid reading, which is a sensor or harness repair, not a user fix.
Dishwasher not cleaning, C6 or C7, or a leak alert
C6 means the incoming water is too cold: GE wants at least 120 F at the dishwasher, so run the kitchen faucet hot before starting a cycle and check the water heater setting. C7 means the water temperature sensor circuit failed and needs a technician. Cloudy glasses and a white film on hard Texas water are scale, not a fault; a citric-acid cleaner and rinse aid fix it. Dishes that come out wet and cycles that run two hours or more point at the heating element. A leak-detected alert on newer GE and Profile models means the base pan sensor got wet: the dishwasher stops and drains on its own, and the leak source needs to be found before it is reset.
Front-load washer shows E22, E23, E31, E60 or E61
On GE front-loaders E22 means the fill took longer than eight minutes: open both supply valves fully, straighten the hoses and clean the inlet screens, which scale blocks on Texas water; if flow is strong and the code returns, the water valve has failed. E23 means the flood-protect switch tripped; one occurrence after a badly unbalanced load can be ignored, a repeat needs service. E31 means a slow drain: clean the pump filter behind the small access door at the bottom front, and check that the standpipe is not above 96 inches. E60 and E61 are the door lock and unlock switches. Newer UltraFresh models show plain-word messages instead and keep the numbered faults in memory: with the washer idle, hold Start for about ten seconds and the stored codes blink on the display; note them before calling.
Top-load washer will not spin, shows dE or LID, or fills slowly
GE top-loaders stop before the spin when the lid is open or the lid lock cannot confirm it is closed, which shows as dE or LID. Clean detergent residue from the latch and check that the lid sits flat. A washer that fills slowly with H2O on the display has the same inlet-screen and valve causes as the front-loaders. If it agitates but never spins, or spins with a loud grinding, the drive system needs a technician. A washer that walks across the floor on the spin is unleveled, and the self-leveling rear legs sometimes need to be freed by tilting the machine forward.
Dryer runs but does not heat, or takes two cycles
On GE electric dryers the thermal fuse or high-limit thermostat opens when airflow is restricted, and the dryer keeps tumbling cold. The vent has to be cleared first, or the replacement fails the same way. On gas models an igniter that glows but the burner never lights, or lights and goes out after a few minutes, points at the flame sensor or the gas valve coils. A dryer that heats but needs two cycles almost always has a blocked vent or a crushed flexible duct behind the machine; in Houston homes with the laundry room far from the exterior wall, the run is often 25 feet and needs cleaning once a year.
Refrigerator shows FF, CC, dE or PF, or ice maker stopped
These are GE's own codes. FF means the freezer temperature is rising; check the food, then look for a sheet of frost on the freezer back wall, which means the defrost system failed. CC means the fresh-food section is out of range. dE means the defrost cycle did not run properly in the last 24 hours. PF means the power was interrupted; clear it and watch the temperatures. DE in capitals is demo mode, which turns the cooling off while the lights work: unplug the refrigerator for a minute or two to leave it. Dirty condenser coils, which pet hair and dust clog fast in Texas, raise temperatures and shorten compressor life. For an ice maker that stopped, replace the water filter if it is older than six months and check for a frozen fill tube before assuming the ice maker itself failed.
Frequently Asked Questions
Is my GE appliance still under warranty?▼
Most GE, GE Profile and Cafe appliances carry a one-year limited warranty on parts and labor; some components, for example the sealed refrigeration system on many refrigerators, carry longer limited coverage. The exact terms depend on the model and are listed on geappliances.com under your serial number. For in-warranty service contact GE Appliances; for out-of-warranty repairs or when you need a same-day slot, call us.
Where is the model and serial number on a GE appliance?▼
Refrigerators: on the inside wall of the fresh-food section, usually near the top. Top-load washers: under the lid or on the back of the control panel. Front-load washers and dryers: inside the door rim. Dishwashers: on the edge of the door or the tub frame. Ranges: behind the storage drawer or under the lip of the cooktop. Have it ready when you call; it lets the technician bring the right part.
Can the SmartHQ app tell me what is wrong?▼
On connected GE, Profile and Cafe appliances the SmartHQ app shows alerts and some diagnostic details, and it can send the appliance data to a technician. It is useful for the first call, but the model number and the code on the display are what we need to bring the right part.
Should I repair or replace my GE appliance?▼
Repair usually makes sense when the quote is under half the price of an equivalent new unit and the appliance is younger than about ten years for washers, dryers and dishwashers or twelve years for refrigerators and ranges. A failed sealed system on an older refrigerator is the common case where replacement wins; most control boards, valves, pumps, sensors and heating components are worth repairing.
Do you use genuine GE parts?▼
We use GE Appliances OEM parts for control boards, water valves, drain pumps, lid locks, sensors and heating components. GE parts are stocked widely in Texas, which keeps most repairs to a single visit.
How much does a GE repair cost?▼
It depends on the part: a thermal fuse, igniter or lid lock sits at the low end, control boards, inverters and compressors at the high end. We quote the full repair upfront after diagnosis and nothing starts until you approve it. Call (888) 771-3235 for a quote.
Can I reset a GE error code myself?▼
Yes. Unplug the appliance or switch its breaker off for one to two minutes. That clears PF notices and many one-off codes. A code that returns on the next cycle is a real fault; write it down, together with the model number, before calling. It shortens the diagnosis.
GE Appliances Repair Near You
We service GE Appliances appliances across Texas major metro areas. Tap a city for local repair details.
Our Samsung fridge stopped cooling overnight. Called Max Appliance and they sent someone out same day. The technician was professional, explained everything clearly, and had us back up and running in under 2 hours. Pricing was fair and transparent. Highly recommend!
Washer was making a horrible noise. The tech arrived on time, diagnosed the issue quickly (worn bearing), and completed the repair efficiently. Very knowledgeable and reasonably priced. Will definitely use them again.
Had an issue with our GE dishwasher not draining. Max Appliance came out the next day, fixed it within an hour, and cleaned up everything. The technician was courteous and explained what caused the problem. Great service!
Our LG dryer stopped heating. Called Max Appliance and they were able to fit us in the same day. The repair was done professionally and the price was exactly what they quoted over the phone. Very satisfied with the service.
Excellent service! Our Whirlpool refrigerator was leaking water. The technician arrived within the scheduled window, quickly identified the problem, and had the parts needed in his truck. Fixed it on the spot. Very pleased!
Called them for our Maytag washer that wouldn't spin. They came out same day, tech was friendly and professional. Fixed the issue and gave us maintenance tips to prevent future problems. Fair pricing too. Would recommend!
Our KitchenAid oven stopped working right before Thanksgiving. Max Appliance saved the day! Same-day service, professional technician, and reasonable rates. We were so relieved. Thank you!
Had them fix our dishwasher last year and they did such a great job we called them again for our fridge. Always reliable, professional, and fair pricing. They're our go-to for all appliance repairs now.
Very responsive and professional. Our freezer stopped working and they came out within hours. The technician was knowledgeable and explained everything clearly. Repair was done quickly and hasn't had any issues since.